A cylindrical pin fin with variable fin base thickness is optimized based on fixed outer radius by using the one dimensional analytic method. Heat loss from the pin fin with fixed outer radius is presented as a function of the fin length. The ratio of in length for optimum heat loss to that for the maximum heat loss is listed. The maximum heat loss and effectiveness and the fin length for the optimum heat loss are presented as a function of fin base thickness and outer radius. One of the results presents the maximum effectiveness decreases rapidly first and then decreases slowly as the fin outer radius increases.

In the Reporting Cell Location Management (RCLM) system, a subset of cells in the network is designated as the reporting cells. Each mobile terminal performs location update only when it enters one of these reporting cells. When a call arrives, the paging is confined to the reporting cell the user last reported and the neighboring bounded non-reporting cells. Frequent location update may result in degradation of quality of service due to interference. Miss on the location of a mobile terminal will necessitate a search operation on the network when a call comes in. We must decide the number of reporting cells and which cell should be reporting cell to balance the registration (location update) and search (paging) operations to minimize the cost of RCLM system. This paper proposes a simulated annealing (SA) for optimization of RCLM system.

This paper is to develop a network reorganization method to consider the constraints which are turn restrictions, U-turns, and P-turns in two way traffic network for Intelligent Transport System(ITS). Several kinds of traffic constraints can be represented in reorganized network using virtual nodes and arc values. The evolution program is also developed to search the multiple shortest paths in this reorganized traffic network within limited time.

In this paper, we implement the taxi telematics service system based on location based service(LBS). The system implementation is composed of 3 major parts : the mobile device with which a user requests taxi calls, the taxi client which resides inside a taxi and supports multimedia environments with navigation function, and the server which manages moving taxies and receives user taxi calls. From the mobile device's GPS information, the server finds the closest taxi which is then sent to the user with the mobile device.

Recently, there have been intensive researches on the wireless Internet access through WiFi WLAN using WiRro network as backhaul link in the Internet service providing business area. However, in the wireless Internet access method, we need to solve the compatibility problem for different user authentications between licensed WiBro network and unlicensed WiFi network for billing and user management. In this paper, we propose an authentication method for WiFi users by BWAN operators through WiNNERs which is RS connecting the two networks, and discuss the effectiveness of the method.

Temperature variation according to space and time on the inner parts of engineering constructions(e.g.: dam, slope) can be a basic information for diagnosing their safety problem. In general, as constructions become superannuated, structural deformation(e.g.: cracks, defects) could be occurred by various factors. Seepage or leakage of water through these cracks or defects in old dams will directly cause temperature anomaly. Groundwater level also can be easily observed by abrupt change of temperature on the level. This study shows that the position of seepage or leakage in dam body can be detected by multi-channel temperature monitoring using thermal line sensor. For this, diverse temperature monitoring experiments for a leakage physical model were performed in the laboratory. In field application of an old earth fill dam, temperature variations for water depth and for inner parts of boreholes located at downstream slope were measured. Temperature monitoring results for a long time at the bottom of downstream slope of the dam showed the possibility that temperature monitoring can provide the synthetic information about flowing path and quantity of seepage of leakage in dam body.

In this study, GAC adsorption, ozonation and $O_3/GAC$ hybrid processes were investigated for treatment of humic acid. The degradation characteristics and efficiencies of humic acid in each process were evaluated through pH variation, $UV_{254}$ decrease, DOC removal, change of molecular size distribution and by-products formation. DOC removal rate in $O_3/GAC$ hybrid process (80%) was higher than arithmetic sum of ozonation (38%) and GAC adsorption process (19%) by synergism. $UV_{254}$ decrease rate of humic acid was also the highest than any other processes when treated in $O_3/GAC$ hybrid process. Molecular size distribution was not significantly changed in the GAC adsorption process. Main distribution of molecular size of humic acid was converted from 3 k~30 kDa into 0.5 k~3 kDa in ozonation. But the most of large molecular sizes of humic acid converted into small molecules(smaller than 0.5 kDa) in $O_3/GAC$ hybrid process. Quantities of formaldehyde and glyoxal formed in $O_3/GAC$ hybrid process were less than the ones in ozonation.

From the extensive screening for small cryptic plasmid among about 23 lactic acid bacteria (LAB), 2.4 kb of cryptic plasmid was isolated from Lactobacillus farciminis strain KCTC 3681 and named as pLF24. The plasmid pLF24 was a circular molecule of 2,396 base-pairs in length with a G+C content of 38%. Two protein-coding sequences could be predicted. ORF1 and ORF2 showed homologies to plasmids of gram-positive bacteria. The replication protein coded by ORF2 and the plus origin, were similar to replication regions of other gram-positive bacteria as shown in plasmids such as pLH2, pLS141-1 and pLC2. The nucleotide sequence of pLF24 was deposited into Genbank data base with an accession number of EU429343. The newly isolated plasmid can be used for construction of shuttle vector in Lactobacillus bacteria.

Rapid production of therapeutic proteins such as angiostatin and endostatin angiogenic inhibititors has been highly demanded for cancer treatment. In this regard, recombinant human angiostatin and endostatin were successfully expressed as soluble forms by maltose binding protein (MBP)-mediated fusion expression in Escherichia coli. PCR amplified, angiostatin and endostatin genes from human placenta cDNA library were inserted into an expression vector pMAL-c2e to construct prokaryotic expression vectors, pMAL-c2e/AS and pMAL-c2e/ES, respectively. Recombinant angiostatin and endostatin were efficiently expressed in E. coli origami (DE3) after IPTG induction and protein expression were confirmed by SDS-PAGE analyses. The expressed recombinant proteins were purified near homogenity using an amylose affinty column chromatography. In contrast that previous E. coli expressions were all insoluble, our results first time demonstrated that MBP fused human angiostatin and endostatin were soluble in E. coli.

The tailings piled in abandoned mines are well-known potential sources of soil contamination. Hydrated limes were applied as cementing materials to solidify heavy metal contaminated tailings for the purpose of reducing their toxicity and migration rates. The optimum mixing ratio of tailings, hydrated lime, and water was determined through a preliminary test. The mixtures of mine tailings and hydrated lime solidified through pozzolanic reaction were tested for their durability against repeated freezing and thawing processes. After repeated freezing and thawing, the uniaxial compressive strengths of all the solidified mixture specimens decreased in comparison with those before test but still higher than $3.5kgf/cm^2$, the standard recommended for land reclamation solids by EPA(Environmental Protection Agency), which suggested that hydrated lime be a potential material to treat the abandoned mine tailings for the environmental purpose.

Reports about coefficients of consolidation in horizontal direction of marine clays located at seven different sites on western and southern coast area in Korea were reviewed and characteristics of them were investigated. As results of analyses, for relation between the depth of ground and coefficients, any trend and correlation between them can not be found since they are more influenced by the nature of geological formation rather than the depth of ground. Dissipation time t50, one of important factors in estimating value of coefficient of consolidation in horizontal direction, was found to be quite related to them. For the correlation between the maximum pore pressure developed and coefficients, coefficient of consolidation in the horizontal direction tend to decrease with increase of the maximum pore pressure whereas the ground water level or static pore pressure do not have any specific correlation with those coefficients. Values of coefficient tends to increase with values of liquid limit, plastic limit and plastic index and thus they are found to be directly influenced by the contents of fines. Values of coefficient of consolidation in horizontal direction are also increased with increases of permeability in horizontal direction and coefficient of consolidation in vertical direction. They were highly correlated between coefficient of consolidation and permeability in horizontal direction while values of coefficient of consolidation in horizontal direction have a relatively low correlation with values of coefficient of consolidation in horizontal direction. Sometimes, coefficient of consolidation in horizontal direction obtained from field tests were estimated 2-3 times greater than those from laboratory tests.

This paper is results of investigating the dominant factors influencing to coefficient of consolidation in horizontal direction of Korean marine clays and their correlations through literature review. From the results of analyzing data obtained from field tests such as piezocone penetration and dilatometer tests as well as laboratory tests, coefficient of consolidation in the horizontal direction was found to increase with increase of stiffness index of soil while it decreases with the increase of dissipation time of pore pressure developed during field tests. In general, the coefficient of consolidation in the horizontal direction tends to increase with increase of undrained shear strength and preconsolidation pressure although correlation between them are relatively low. Friction ratio has a high correlation with coefficient of consolidation in the horizontal direction in case of friction ratio being greater than 1.0. For methods of estimating coefficient of consolidation in the horizontal direction with different testing device, values obtained from methods of P2-logt and DMT-A with dilatometer were quite similar to values from piezocone penetration test. Consistency of soil is quite proportional to coefficient of consolidation in the horizontal direction. Clear correlation between coefficients of consolidation in the horizontal and the vertical directions could not be found. coefficient of consolidation in the horizontal direction estimated from the results of field test tends to be 1.13~3.11 times greater than that obtained from laboratory tests.

Applicability of existing methods of predicting consolidation settlement was assessed by analyzing results of centrifuge tests modelling self-weight consolidation of soft marine clay. From extensive literature review about self-weight consolidation of soft marine clays located in southern coast in Korea, constitutive relationships of void ratio-effective stress-permeability and typical self-weight consolidation curves with time were obtained by centrifuge model experiments. For the condition of surcharge loading, exact solution of consolidation settlement curve was obtained by Terzaghi's consolidation theory and was compared with the results predicted by currently available methods such as Hyperbolic method, Asaoka's method, Hoshino's method and ${\sqrt{S}}$ method. All methods were found to have their own inherent error to predict final consolidation settlement. From results of analyzing the self-weight consolidation with time by using those methods, Asaoka's method predicted the best. Hyperbolic method predicted relatively well in error range of 2~24% for the case of showing the linearity in the relationship between T vs T/S in the stage of consolidation degree of 60~90 %. For the case of relation curve of T vs $T/S^2$ showing the lineality after the middle stage, error range from Hoshino method was close to those from Hyperbolic method. However, Hoshino method is not able to predict the final settlement in the case of relation curve of T vs $T/S^2$ being horizontal. For the given data about self-weight consolidation after the middle stage, relation curve of T vs T/S from ${\sqrt{S}}$ method shows the better linearity than that of T vs $T/{\sqrt{s}}$ from Hyperbolic method.

In general, non-stationary or chaos time series forecasting is very difficult since there exists a drift and/or nonlinearities in them. To overcome this situation, we suggest a new prediction method based on multiple model TS fuzzy predictors combined with preprocessing of time series data, where, instead of time series data, the differences of them are applied to predictors as input. In preprocessing procedure, the candidates of optimal difference interval are determined by using con-elation analysis and corresponding difference data are generated. And then, for each of them, TS fuzzy predictor is constructed by using k-means clustering algorithm and least squares method. Finally, the best predictor which minimizes the performance index is selected and it works on hereafter for prediction. Computer simulation is performed to show the effectiveness and usefulness of our method.

Since the hydraulic fracturing field testing method was introduced first to Korean geotechnical engineers in 1994, there have been lots of progresses in a hardware system as well as an interpretation tool. The hydrofracturing system of first generation was the pipe-line type, and it has been developed to a wire-line system at their second generation. The current up-to-date system is more compact and is able to be operated by all-in-one system. With a progress in a hardware system, the software for analyzing in-situ stress regime has also been progressed. The shut-in pressure, which is the most ambiguous parameter to be obtained from hydrofracturing pressure curves, can now be acquired automatically from the various methods. While the hardware and software for hydrofracturing tests are being developed during the last decade, the author could accumulate the field test results which can cover the almost whole area of South Korea. Currently these field data are used widely in a feasibility study or a preliminary design step for tunnel construction in Korea. Regarding the difficulties in a site selection and a test performance for the in-situ stress measurement at an off-shore area, the in-situ stress regime obtained from the field experiences in the land area can be used indirectly for the design of a sub-sea tunnel. From the hydrofracturing stress measurements, the trend of magnitude and direction of in-situ stress field was shown identically with the geological information in Korea.

This paper presents the conductance model at high frequency of the Ceramic Metal Halide Lamp and the designing method of the electronic ballast with the LCC resonant tank type by using that model. Conductance model is based on a physical phenomenon in the discharge tube of the lamp and model constants of conductance model are obtained by Least Squares Method. After equivalent impedances are determined by the conductance model, The LCC resonance tank is designed by using the equation of the lamp power. Simulation result using PSpice software and experimental results show that the conductance model in this paper is very useful to design the electronic ballast at high frequency for the Ceramic Metal Halide Lamps.

This paper studied the sensitivity characteries of the electronic ballast for the discharge lamps, which implies variation ratio of the output power by the passive element variation. We have derived the equation to represent the lamp power, and obtained the sensitivity characteristic equations. The simulation result shows that the proposed equations are correct and very useful to design the electronic ballast with the LCpCs-type resonant tank.

A method to reduce seam line artifact in spatial compounding of ultrasonic images is presented. Spatial compounding is a speckle reducing imaging technique in which a number of ultrasound images of a given target that have been obtained from multiple view angles are combined into a single compounded image by combining the data received from each data point in the compounded image. Since different view angle results in different view area, and the images of different view arms are combined into an image, the compounded image consists of regions with different signal to noise ratio, and the boundary lines between these regions are visible as seam lines in the compounded images. In this paper, we present an algorithm that reduces the visibility of this seam line in the spatially compounded images. Design procedure for a FIH filter is described and the results of applying the filter to in-vivo ultrasonic images are analyzed.

In this paper, the Proper Orthogonal Decomposition (POD) method, which is a statistical analysis technique to find the modal characteristics of a structure, is adapted to identify the modal parameters of a tall chimney structure. A wind force time history, which is applied to the structure, is obtained by a wind tunnel test of a scale down model. The POD method is applied on the wind force induced responses of the structure, and the true normal modes of the structure can be obtained. The modal parameters including, natural frequency, mode shape, damping ratio and kinetic energy of the structure can be estimated accurately. With these results, it may be concluded that the POD method can be applied to obtain accurate modal parameters from the wind-induced building responses.

A real-time face detection is to find human faces robustly under the cluttered background free from the effect of occlusion by other objects or various lightening conditions. We propose a face detection system for real-time applications using wavelet decomposition method based on Gabor features. Firstly, skin candidate regions are extracted from the given image by skin color filtering and projection method. Then Gabor-feature based template matching is performed to choose face cadidate from the skin candidate regions. The chosen face candidate region is transformed into 2-level wavelet decomposition images, from which feature vectors are extracted for classification. Based on the extracted feature vectors, the face candidate region is finally classified into either face or nonface class by the Levenberg-Marguardt back-propagation neural network.

A reliability model of Level II AFDA is developed to analyze the stability of armor units on the sloped coastal structures. Additionally, the partial safety factors of random variables related to armor units can be straightforwardly evaluated by applying the inverse-reliability method in which influence coefficients and uncertainties of random variables, and target probability of failure are combined directly. In particular, a design equation for armor units is derived in terms of the same criteria as deterministic design method in order to apply the reliability-based design method of Level I without some understanding to the reliability analysis. Finally, it is confirmed that several results redesigned by the reliability-based design method of Level I have satisfactorily agreement with results of CEM as well as those of Level II AFDA.

Level II AFDA and Level III MCS reliability models are applied to analyze the stability of armor units on trading and coastal harbors in Korea. Hudson's formula and Van der Meer's formula are used in this reliability analysis. Also, probability density functions of reliability index and probability of failure are derived by the additional analysis. In addition, the partial safety factors of all harbors related to armor units can be straightforwardly evaluated by the inverse-reliability method. The upper and lower limits and average level of partial safety factors can be statistically investigated with the results of all cases applied in this paper. Therefore, it may be possible to design armor units of new breakwaters including the uncertainty of random variable and target level by using the present results.

In this paper, the analysis on type effect of inverter output voltage distortion on the control of an induction motor is discussed. The inverter output voltage is distorted differently from the reference voltage owing to the inverter nonlinear characteristic. The inverter nonlinear characteristic results from the voltage drop, the inherent characteristic of the power semiconductor, and the dead time for preventing the short circuit of the inverter leg. This characteristic distorts the inverter output voltage and then, causes the motor flux estimation error. Although this characteristics do not significantly effect in the general-purpose induction motor control, but significantly effect on the low-speed operation of high performance motor control such as the sensorless vector control.

This study reviewed and compared the measured value with the calculated sediment loads value by the existing theory equation, after actually measuring the suspended load, focusing on locality river in Gangwon province. Next, it suggested the application problems of the existing sediment loads calculation equation in case of rivers in Gangwon province, and suggested the proper sediment loads calculation equation to rivers in Gangwon province, after implementing the statistical regression analysis by using the measured data for 5 rears, 2003 ~ 2007.

This study tried the 1st, 2nd dimensional numerical analysis according to the pier's shape, size and installing method in order to compare the depth of scour calculation method using the variables calculated by using the 2nd dimensional numerical analysis with the calculated depth of scour value by using the calculated variables by using the 1st dimensional numerical analysis. And then verified the problems occurring when the depth of scour is calculated by using the calculated values by using the 1st dimensional numerical analysis, as calculating the deviation depending on it.

When the existing polder levee was constructed, the river's numerical analysis decided the bank raise by applying the planned flood stage or by using the result from the sectional 1st dimensional numerical analysis. But, it was presented that there is a limitation in the 1st dimensional value analysis when the structure like the polder levee obstructs the special shaped running water flow. Therefore, in order to verify the numerical value applicability when the polder levee is constructed, this report compared each other through the 1st and 2nd dimensional numerical analysis and the mathematical principle model laboratory. In case of the polder levee construction through the numerical analysis and the mathematical principle model laboratory, it was decided that there was no big problem in the 1st dimensional numerical analysis applied design, considering the uncertainty of mathematical principle analysis though the first dimensional numerical analysis was calculated a little bigger than the second. But, after construction, it was found that the water level deviation of the 1st, 2nd occurred biggest at the place where the flow was divided into two. Also, as a result of comparing the 1st, 2nd dimensional numerical analysis with the mathematical principle model laboratory, it was confirmed that the 1st numerical analysis applied design decreased the modal safety largely, as the left side water level was calculated smaller more than 0.5m in case of the 1st dimensional numerical analysis.

A linear wind prediction program, WAsP, was employed to predict wind speed at two different sites located in complex terrain in South Korea. The reference data obtained at locations more than 7 kilometers away from the prediction sites were used for prediction. The predictions from the linear model were compared with the measured data at the two prediction sites. Two compensation methods such as a self-prediction error method and a delta ruggedness index (RIX) method were used to improve the wind speed prediction from WAsP and showed a good possibility. The wind speed prediction errors reached within 3.5 % with the self prediction error method, and within 10% with the delta RIX method. The self prediction error method can be used as a compensation method to reduce the wind speed prediction error in WAsP.

Set-valued attributes appear in many applications to model complex objects occurring in the real world. One of the most important operations on set-valued attributes is the set join, because it provides a various method to express complex queries. Currently proposed set join algorithms are based on block nested loop join in which inverted files are partitioned horizontally into blocks. Evaluating these joins are expensive because they generate intermediate partial results severely and finally obtain the final results after merging partial results. In this paper, we present an efficient processing of set join algorithm. We propose a new set join algorithm that vertically partitions inverted files into blocks, where each block fits in memory, and performs block nested loop join without producing intermediate results. Our experiments show that the vertical bitmap nested set join algorithm outperforms previously proposed set join algorithms.

MIL-HDBK-217 has widely been used for electronics reliability predictions. Recently, the $217Plus^{TM}$ has been developed by DoD RIAC and may replace MIL-HDBK-217. A overview of the $217Plus^{TM}$ has been performed in this paper. We first reviewed the overall concepts and reliability prediction procedures. We then explained the component models and the system level model with process grading concepts. Bayesian approach incorporating field data into the predicted failure rate is another feature of this methodology.

Reliability predictions for selected electronic parts using 217-Plus have been performed in this study. 217-Plus has recently developed and may be applied for electronics failure prediction as a surrogate of MIL-HDBK-217. We first briefly reviewed 217-Plus component models. Based on three selected components, predictions using both MIL-HDBK-217 and 217-Plus have been made and the results were compared. Even though the comprehensive conclusion may be drawn from extensive component and system level analyses, the results in this study may provide general insights towards reliability through two specifications.

In this paper, we have developed wavelength swept laser system for the swept source optical coherence tomography(SS-OCT). A laser is constructed by using the two SOAs parallel configuration, fiber Fabry-Perot tunable filter(FFP-TF). The wavelength sweeps are repetitively generated with the repetition period of 50Hz. The wavelength tuning range of the laser is more than FWHM of 80nm centered at the wavelength of 1310nm and the line-width of the source is 0.12 nm.

We have realized the swept source optical coherence tomography(SS-OCT) by using the self-fabricated wavelength swept laser(wavelength tuning range : 80nm, line-width : 0.12nm, wavelength sweeping rate : 50Hz). In addition, we have used the dual balanced detector that could make a mirror image in OCT display suppressed. We can also fabricate the comb filter of Michelson interferometer type for fast-signal processing in OCT. Using this SS-OCT system for measuring an mirror, a 1mm-depth glass and an onion, we confirmed that the in vivo epidermal cross-sectional images for them can be obtained appropriately.

Recently, mobile devices have supported wireless LAN as well as bluetooth, where the services such as heterogeneous network access and seamless mobility connection are important. Even though the mobility and physical network might be varied, an efficient communication mechanism for the network access and a robust mobility management of mobile devices are needed. In this paper, we design and implement a Bluetooth system with mobile LAN access capability. The proposed system has the following features; 1) IP connection is enabled by BENP in the link layer, 2) The networks devices of heterogeneous mobile devices are integrated into a single virtual network interface, 3) IP mobility between the bluetooth and wireless LAN is supported by mobile IP. The experimented results show that the packet loss and delay time during the handover duration is reduced by predicting the handover among different networks followed by the setup of any required parameters in advance.

Metamaterial are artificial structures that can be designed to exhibit specific electromagnetic properties not commonly found in nature. Metamaterial transmission lines are usually fabricated with a microstrip structure and it's equivalent circuit is composed of two series capacitances and a shunt inductance. However microstrip structure need a via hall for realizing a shunt inductance. To eliminate via hall, we proposed a CRLH transmission line using a CPW structure, and obtained equivalent circuit values, line parameters.