Corrosion and tensile properties of zircaloy-4 cladding tube having a laser welding part in elevated temperature are studied to present the criterion of quality evaluation in nuclear reactor and to found the scientific basis of SCC, with laser welding method using by coupling up cladding tube to end cap. In the result of tensile test(40$0^{\circ}C$), the fracture is not happened in the welding part but base metal and the result of corrosion test(40$0^{\circ}C$ 1500psi steam), corrosion rate of the molten zone and PMZ is a little higher than the other zone

This study introduces the new way for the evaluation criteria of the Mash-Seam Tailored Blank weldability, The materials used are low carbon automotive galvanized and high strength steels and the evaluation of weldability are examined with various thickness. Welding tests were conducted for both similar thickness and dissimilar thickness cases. The criteria developed for optimum welding conditions were based on the relationship among results of die press forming test, forming limit diagram, Erichsen test and microhardness measurements. The application of the developed criteria(fracture ratio, strength ratio, etc) in obtaining optimum welding condition revealed that a weld which satisfied ant of the criteria did not fracture during actual die press test and FLD dome test.

We propose an implicit numerical implementation for Leblond's transformation plasticity constitutive equations , which are widely used in welded steel structure. We apply Euler backward scheme rule to integrate the equations and determine the consistent tangent modulus. The implementation may be used with updated Lagrangian formulation. we test a simple butt-welding process to compare with SYSWELD and discuss the accuracy.

The main characteristic of the Electron Beam Welding technique is its high energy density which produces thin and deep welds with very little distortion. High accelerated electrons, focused in a beam of 0.5 ∼ 2mm diameter, produce narrow welds with deep penetration. The result is a small HAZ as well as a low and uniform distortion which is predictible within very narrow limits. But the small diameter of the EB increases the requirements for the equipment control system for centering the beam on the welding joint in order to avoid any lack of fusion. Therefore, in this paper, we introduce the system developed at our company and the quality of welding zone, the detail function of system.

Laser cladding processing allows rapid transfer of heat to the material being processed with minimum conduction into base metal, resulting in low total heat input. The effects of $CO_2$ laser cladding with powder feeding on mechanical properties of VERSAlloy were studied. Their low melting point (under 1093$^{\circ}C$) enables overlays to be applied with minimum dilution and base metal distortion. Experiment results indicated that powder feeding speed and quantity were important for laser cladding with powder feeding. The powder feeding speed should be adapted according to cladding speed for good shaping of clad layer. The effect of heat on the HAZ size can be limited and the growth of grain size of HAZ size was not serious.

This paper describes the weldability of JIS S45C medium carbon steel (same material with KS SM45C and SAE 1045) for machine structural use by Nd:YAG laser. This material have a limitation to the industrial application in spite of good mechanical characteristics. This is due to its difficult welding work from high carbon contents. We therefore have investigated laser weldability of this material to extend the application of medium carbon steel. The results of this study provide application possibility of Nd:YAG laser welding for medium carbon steel.

항공기의 제트 엔진을 비롯하여 육상용 발전기, 선박용 엔진, 로켓 엔진 등에 널리 사용되는 터빈 블레이드를 포함한 고온용 가스터빈 부품은 최대 온도 120$0^{\circ}C$ 이상의 고온에 노출되어 가혹한 기계적 응력을 받는 동시에 고온에서의 표면 안정성이 요구되므로 초내열 니켈 합금(superalloy), 티타늄 합금, 내열강 등의 고온강도가 우수한 합금이 사용된다. 그런데 합금성분이 많이 첨가된 내열 합금을 용접하는 경우, 미세균열, 용접부의 기계적 성질의 저하, 용접열영향부의 내식성과 내산화성의 저하, 용접외부 결함에 의한 피로강도 저하 등의 문제가 발생하므로 이를 해결해야 한다. 본고에서는 생산성과 용접품질이 우수한 고밀도 에너지빔 용접의 적용 현황에 관하여 고찰코자 한다.

Quality estimation of the weld has been one of the important issues in RSW which is a main process of the sheet metal fabrication in auto-body industry. It was well known that among the various welding process variables, dynamic resistance has a close relation with nugget formation. In this study, a new quality estimation algorithm is developed with the primary dynamic resistance measured at welding machine timer. For this, Back propagation algorithm of neural network is used.

The average grain size, the grain-size distribution, the morphology and the microstructure are fundamental characteristics of a spraying powder. Now that the significance of the grain size for the pattern of properties of the powder has been recognised, greater consideration is also being given to it in standards and regulations. However, unfortunately, the processes according to which the grain size and the grain-size distribution must be determined are specified in the rarest of cases. The contribution therefore dealt with the comparison of different particle-size measuring techniques, such as diffraction spectroscopy, sedimentation, sieving and microscopic measurement. The comparability of the measured results was investigated on twelve plasma spraying powders with different compositions, nominal sizes and morphologies.

Fatigue behaviour of eight different hollow section T-joints was investigated experimentally using scaled steel models. The joints had circular brace members and rectangular chords (CRHS). Hot spot stresses and the stress concentration factors (SCFs) were determined experimentally. Fatigue testing was carried out under constant amplitude loading in air. The experimental SCF values for CRHS joints were found to be between those of circular-to-circular (CCHS) and rectangular-to-rectangular (RRHS) hollow section joints. The fatigue strength referred to experimental hot spot stress was in reasonably good agreement with current fatigue design codes for tubular joints.