Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference (한국조명전기설비학회:학술대회논문집)
The Korean Institute of IIIuminating and Electrical Installation Engineers
- 기타
Domain
- Electricity/Electronics > Home/Electric Appliances
1999.11a
-
Discharge characteristics research for high voltage and large current electric machinery design, the development of ozonizer with high yield and efficiency for environment improvement, generation of plasma & laser and EMI EMC are research fields of Enersy & Environment Electromagnetic Laboratory(EEEL) in the school of electrical & electronic engineering of Yeungnam University. On this paper, we would like to introduce the discharge and ozone generation characteristics of ozonizers designed and manufactured by EEEL. After starting research for fluid gas discharge characteristics early in the 1980's, high voltage nozzle(HVN) type ozonizer, neon lamp(Nelamp) type ozonizer, ozone lamp(Olamp) type ozonizer and multi-discharge type ozonizer(MDO) have been investigated since 1990.
-
In this paper a new discharge type ozonizer comprising the superpose operation of silent and surface discharge is presented. The ozonizer consists of two concentric glass tubes with three type of discharge electrodes : the external electrode(EE), the internal electrode(IE) and the central electrode(CE). By varying the structure of IE and materials of CE, we analyzed the characteristics of ozone related different parameters including
$O_{3con}$ ,$O_{3g}$ , and$O_{3Y}$ . Using Cu made CE it was found the O3con is higher with Cu tape than that with Cu coil wound IE. At Q = 1[l/ min] the values of O3con were found as 3000[ppm] with Cu tape wound IE and 1898[ppm] with Cu coil wound IE. Then using SUS wire made CE with Cu tape wound IE at Q = 1[ι/ min] the maximum value of O3con was found as 5632[ppm]. It was observed that both$O_{3con}$ and$O_{3y}$ are higher with SUS made CE than that with Cu made CE. The maximum values of$O_{3Y}$ were found as 79[g/kWh] with Cu made CE and 170[g/kWh] with SUS wire made CE. -
The manufactured pulsed power system with 500kA current is described in this paper. The capacitor bank, control cabinent, dec charging unit, closing switch and dumping box, cable system etc. employed with the system components are described. Especially the development of the inverse pinch switch controlled by gas puffing enabled the generation of the very high voltage and current.
-
Both conventional and PI3 implanters require dense sources for high productivity rate, and small sheath expansion in PI3 besides. The problem of the creation of large volume uniform plasma in PI3 facilities replaces that of beam forming in accelerators. Some aspects of ion extraction in both cases and Langmuir probe plasma diagnostics with be discussed. Plasma parameters of large volume multicusp dc hot cathode and inductively coupled RF plasma sources obtained with Langmuir probe and ion mass analyzer with be presented. Design features and performances of high current Freeman and ECR ion sources will be described.
-
The effect of addition of noble gases on negative hydrogen ion production in a dc filament dischargeThe effect of the addition of helium, neon, argon and xenon on the production of negative hydrogen ions has been studied in a magnetically confined dc filament discharge. The addition of helium and neon produced effects similar to an equivalent increase in hydrogen pressure. However, the addition of argon and low fractions of xenon produced significant increases in the negative ion density for hydrogen at pressures around 1 mTorr. The addition of argon and xenon, by increasing electron density and decreasing electron temperature, achieved conditions closer to optimum for negative ion production. The largest enhancement of negative hydrogen ion density occurred with the addition of argon; it is suggested that this is due to a resonant energy exchange between excited argon atoms and hydrogen molecules.
-
Laser diagnostics have been extensively used to understand plasma behaiviour under different discharge conditions. Measurements were performance for (i) electric field, (ii) electron temperature and density, and (iii) reaction products due to chemical reactions by electron impacts. The knowledge thus gained has been extensively used to realize novel plasma performances, such as epitaxial thin film depositions using plasma sputtering, performance improvements of discharge-pumped excimer laser, and developments of environmental equipment.
-
To investigate the discharge dynamics of alternating current plasma display panel (ACPDP), we measured the spatio-temporally resolved VUV and IR emission by an intensified charge coupled device (CCD). The breakdown beings around the anode inner edge and moves towards the cathode surface. As the ionization intensifies in front of the cathode surface, another emission region appears on the anode surface. While the anode side emission does not move but grows, the cathode side emission moves out and spreads over the entire cathode surface. The discharge dynamics emission by a 2 dimensional numerical simulation suggests that a cathode-directed streamer formation play an important role.
-
In order to analyze the discharge-pumped KrF excimer laser, computer simulation code is developed. On the other hand, the electron velocity distribution in a discharge plasma, measured by the Thomson scattering method, showed the Maxwellian, while the code predicted non-Maxwellian. This disagreement was solved by introducing the electron-electron collision into the simulation code. We also developed a simulation code on the CO2 laser-heated plasma in high-pressure Ar gas, and estimated the formation process of Ar2 excimer. The code predicted the possibility of the Ar2 laser action at 126 nm.
-
This paper describes preliminary discussions on manufacture of a He-Ne laser and investigation of output characteristics. The He-Ne laser which is to be manufactured is what is the most common wavelength λ=632.8[nm] transition in the red portion of the spectrum. The output characteristics as various parameters, such as gas mixture ratio, gas pressure, discharge current, resonator, resonator length, and the efficiency characteristics as a input power will be investigated.
-
This paper describes the temperature characteristics and influence produced from the unification of Magnetic Ballast and simple Electronic starter for fluorescent lamp. This is affected by the transmitted Temperature from a part of Ballast loss in half-wave rectifier electronic starter. The simulation and experiment show that characteristics of capacitor in electronic starter is changed by the high temperature(80
$^{\circ}C$ ) of magnetic ballast, and preheating time of lamp is reduced by it. -
This paper describes real power difference continuous and on/off operation of ballast for fluorescent lamps. We tested ballasts for fluorescent lamps, such that glow stater ballast, rapid stating ballast, and electronic ballast. We measured consumed real power. Input voltage is A.C. 220V and ON time 8 is minutes, OFF time 2 is minutes.
-
Sunlight Collector System is a new way to make sunlight available to living things. It transmits sunlight through fiber optics to wherever is needs. It applies the artificial lighting, underground lighting, intelligent building, museum lighting, restoration-room to health etc. Cutting out most of the ultra-violet and intra-red radiation. In this paper, we measured the spectrum analysis of sunlight and Sunlight collector System's light. Also, we found out the distance to get visible light.
-
일반적으로 반사판의 반사율이 변화하거나, 사용하는 램프의 크기가 변화하면, 동일형상의 조명기구에서도 기구 효율이 변화하는 것으로 알려져 있다. 본 연구에서는 이와 같은 기구 효율변화가 어느 정도인지 알아내기 위하여, 형광등 기구의 확산 반사판과 경면 반사판의 반사율 변화와, 직관형 형광램프의 직경 변화에 따른 기구효율 변화를 시뮬레이션을 통하여 계산하여 보았다. 계산 결과 반사판의 반사율이 상승함에 따라, 그리고 램프 관직경이 감소함에 따라 기구 효율이 상승하며, 이를 이용하여 큰 에너지 절감을 도모할 수 있을 것으로 판단된다.
-
This paper describes preliminary discussions on spatial distribution of NO density, which is mostly contained in simulated NOX exhaust, between a wire-cylinder geometry discharge gaps by using Laser Induced Fluorescence(LIF) Spectroscopy. Spatial distribution of NO density will be measured with varying NO concentrations from 166 to 644[ppm] and diameters of central electrode from 6 to 10mm. Pulsed Nd:YAG laser, Optical Parametric Oscillator(OPO), and Frequency Doubler are used to excite NO molecules to their excited state.
-
The object of this paper is design and to make a high efficiency magnetic ballast for high pressure sodium lamp. The results show the efficiency is 10[%] up compared with standard ballast in best case.
-
본 논문은 입력전압 파형을 각각 같은 크기의 정현파, 구형파, 삼각파로 변화시켰을 때, 형광램프의 시동특성ㅇㄹ 어떻게 달라지는 지에 대해 비교 설명한 논문이다. 구형파가 입력으로 주어질 때 램프의 시동특성은 현저하게 떨어져, 시동전압이 크게 상승하는 것을 볼 수 있었으며, 삼각파의 경우는 대체적으로 정현파 입력과 거의 동일한 특성을 나타냈다.
-
This paper introduces a fluorescent lamp model based on gas discharge phenomena. This model was applied to electronic ballast. Simulation and experimental results were presented to verify the feasibility of the modeling.
-
This paper shows a structure for an electronic ballast of HID lamps. An electronic ballast for HID lamps usually employs a high-frequency resonant inverter and voltage-to-frequency converter to control the output. A half-bridge and series resonant circuit are chosen for the ballast. The inverter with V/F converter is modeled with a transfer function and a self-feedback controller is proposed. This structure is analyzed and the feedback gain is determined by using the inverter model. Experimental system is built with a commercial 250W high pressure sodium lamp and the results show a validity of the proposed ballast.
-
In this paper, to bring under robust and accurate control of auto-equipment systems which disturbance, parameter alteration of system, uncertainty and so forth exist, neural network controller called dynamic neural processor(DNP) is designed. In order to perform a elaborate task like as assembly, manufacturing and so forth of components, tracking control on the trajectory of power coming in contact with a target as well as tracking control on the movement course trajectory of end-effector is indispensable. Also, the learning architecture to compute inverse kinematic coordinates transformations in the manipulator of auto-equipment systems is developed and the example that DNP can be used is explained. The architecture and learning algorithm of the proposed dynamic neural network, the DNP, are described and computer simulations are provided to demonstrate the effectiveness of the proposed learning method using the DNP.
-
In this paper, using a wide-band AE sensor with the frequency range from 100[kHz], the frequency spectra of AE signals generated from the corona discharges of the needle-plane electrode was analyzed to determine the proper ultrasonic sensor. We also examined the relationship between the magnitude of corona discharge and the magnitude of AE signals in peak-to-peak value under the application of 60[Hz] AC high-voltage in oil. From these results, the main frequency spectra of AE signals emitted from the corona discharges of the needle-plane gap were found to be 130[kHz] by the fast fourier transform. The magnitude of AE signals was proportional to the magnitude of corona discharge and discharge current pulse with increasing the applied voltages. Also the detection of corona discharge point location by AE signals was found to be possible by using two sensors.
-
In this work, two approaches were proposed for the recognition of partial discharge patterns. The first approach was neural network with backpropagation algorithm, and the second approach was angle calculation between two operator vectors. PD signal were detected using three electrode systems; IEC(b), needle-plane and CIGRE method II electrode system. Both of neural network and angle comparison method showed good recognition performance for the patte군 similar to the trained patterns. And the number of operators to be used had a great influence on the recognition performance to the untrained patterns.
-
Measurements of AE signals caused by partial discharges were performed by using an ultrasonic measurement technique to diagonise the electrical treeing deterioration in XLPE cable. We also examined the partial discharge magnitude and AE signals(peak-to-peak) with the increase of the deterioration time. From these results, it was found that AE signal due to partial discharge can be greatly detected at the peak value of positive polarities prior to the breakdown voltages, and the magnitude of AE signals was closely related to the current pulses by the increase of deterioration, and it appeared that AE signals(peak-to-peak) was proportional to partial discharge magnitude. Attenuation and time-delaying characteristics of ultrasonic signals propagated in various polymers sample by using ultrasonic oscillation and receiving systems are also reported as a basic data of ultrasonic measurements in XLPE cable.
-
This paper offer fundamental ones about insulation diagnosis with electromagnetic wave, when discharges occurred. To simulate Partial-Discharge(PD), It is used needle-plane electrode in air. As the voltages applied, measure the electromagnetic wave with monopole antenna and analysis its fundamental characteristics, then, acquired data were operated. The results presented as the form of graph, and the magnitude of charge when occurred PD simultaneously. In conclusion, when the magnitude of charge over 100[pC], the electric field strength changed, and then the magnitude of charge and the electric field strength increased samely.
-
In this paper, multi gap type ozonizer(MGO) has been designed and manufactured. The ozonizer is equipped with three electrodes(central electrode of screw shape, internal electrode and external electrode) of cylinder shape. This paper describes the following two characteristics:
$\circled1$ The characteristics of discharge with variation of output voltage of AC H.V source, flux of oxygen supplied gas and discharge voltage.$\circled2$ The characteristics of ozone generation by varying flux and discharge power. -
This paper represents the characteristic analyses for the etching in SF6 plasma and the plasma itself, based on the specific knowledges on the discharge mechanism of SF6 plasma which is widely used for the applications of dry etching, using Radio Frequency Inductively Coupled Plasma (RFICP) by measuring electron density, electron temperature then observing their relationship to find the effect of discharge mechanism of SF6 plasma to the etching in contrast to the existing method of finding optimal discharge condition by heuristic.
-
In this paper, a plate type ozonizer has been designed and manufactured to minimize the size of ozonizer. This ozonizer have following benefits : \circled1 convenience of shift and installation \circled2 maximize space utility. Therefore, ozone generation characteristics have been investigated by varying flow rate, supplied voltage and gap spacing of plate electrodes.
-
This paper presents a Single-phase Semi-Bridge PWM Converter, which features Continuos Conduction Mode and Phase-adjusted Unipolar PWM Method. The reduced conduction losses are achieved by the employment of a single converter, instead of the typical configuration composed of a front end rectifier followed by a boost converter. Theoretical principle of operation, a design example and Simulation results of a 3kW Semi-Bridge PWM converter with 220 Vrms input voltage and 400 Vdc output voltage are presented.
-
In Auxiliary block of High speed train Power factor correction and Harmonics reduction is very important issue for efficient energy transport. The GTO-equipped PWM converter is used for traction untill resently. but the rising power capability of IGBTs resently allows to build IGBT-equipped PWM converter with a considerably increases switching frequency. In this paper presents switching pattern, control method, operation mode and tuned filter to reduce dc link voltage ripple for paralleled converter.
-
This paper describes the influence of conducting particle within the coaxial cylindrical electrodes gap under alternating voltage condition investigated using charge simulation method. If the conducting particles precent in the gas insulated system, they can cause decrement of breakdown voltage. Thus, three dimensions computations of electric fields and electrostatic forces have been carried out according to particle location. The results show a good agreement with those of outside country, which can offer a practical reference on the insulation design of domestic GIS.
-
In this paper the approximated analysis method of industrial distribution system using PTW(Power Tools for Windows). System input data, cable impedance and transformer data etc., were calculated by the approximated method using EMTP(Electro Magnetic Transient Program). The effectiveness of this method was improved by electrical characteristics analysis of real factory.
-
This paper presents the effective design of the change of average illuminance and the arrangement of lamps by changing the form of working area and adjusting the distance between the wall and light. This study is intended to simplify the complex calculation of illuminance through the development of application program. It's plan to study application programs that can attain the value of advanced uniformly-distributed illuminance and average illuminance by changing the distance between the horizontal/vertical wall and lamp and between the horizontal/vertical lamp and lamp.
-
This paper is about the design of half-bridge inverter controller with low cost and simple configuration for low power single-phase induction motor driving. The simple controller is composed of MCU and PLD. Also, to limit the overcurrent at initial driving, auxiliary function is added, and stabilizes the system. In order to verify the performance of the proposed methode, we design 500W inverter system, and in result, the response time of the proposed method compared with line voltage driving method is reduced by 200[msec].
-
The power semiconductor switching devices(PSSD) continuously developed, Power Electronic Technology using PSSD is gradually extended. The high frequency inverter to generate the large power high frequency subject to power electronic technology pursuit various applications. Also, in emboss with environmental destruction problem cause the atmosphere and the water pollution to growth of the commercial society, the research in favor of cleaning environmental a pollutant actively proceed. Therefore, This paper describe study on the high frequency pulse power supply. The theoretical results are in good agreement with the experimental ones. The proposed pulse power supply is considerated to be useful for discharge lamp.
-
This paper proposes a current-fed type high frequency inverter using a soft switching technology Zero-Voltage-Switching to reduce turn on and off loss at the switching. The analysis of the proposed circuit was described by using normalized parameter and operating characteristics have been evaluated as to switching frequency and parameters. The theoretical results are in good agreement with the experimental ones. In the future the proposed circuit is considered to be useful for induction heating applications.
-
Since more than Building Decorative Floodlighting in an Architecture is used for improving image at city, the importance of an efficient Building Decorative Floodlighting in an Architecture can't be overemphasized. The purpose of this study was to develop a Building Decorative Floodlighting process model, through analyzing, measuring brightness of real Building Decorative Floodlighting forms in night of Seoul. The results of the study can be summarized as: Building Decorative Floodlighting process model consists of four major which are
$\circled1$ Building Audit$\circled2$ Building Analysis$\circled3$ Selection Opportunities$\circled4$ Follow through -
도로 조명에 있어서 질적인 평가 기준으로서 중요한 위치를 차지하고 있는 휘도 개념은 노면의 반사 특성에 따라 크게 좌우된다. 또한 노면의 반사 특성은 도로가 설치된 이후로부터의 시간, 날씨의 변화, 주어진 구간 내에서의 교통량 등에 의한 노면 재질의 마모 상태에 따라서 복합적으로 변화한다. 그러므로 도로 조명의 설치에 있어서 노면 반사 특성의 측정은 매우 중요할 뿐만 아니라 국내 도로 조명 설비의 휘도 기준을 상정하는데 있어서도 매우 중요하다. 이에 따라서 일반적으로 국내에서 사용되는 4가지의 도로 포장 시료인 콘크리트 도로 샘플, SMA(Stone Matrix Asphalt), 투수성, 밀입도 도로 샘플을 취하여 그 특성을 파악하고 반사 특성에 대한 초기값을 측정하였으며 각 샘플들에 대한 재질의 마모 상태에 대하여 반사 특성의 변화를 각각 측정하였다. 또한 그 측정한 값들을 각각 분석하고 재질의 마모에 따른 평균 휘도 계수 Q0, 정반사 인자 S1, S2값의 변화를 그래프로 제시하였다.
-
빛의 3원색 Red, Green, Blue를 조합하여 분광조성을 달리하면 원하는 광색을 낼 수 있다. 이를 하나의 광원 형태로 개발하면 응용의 폭이 넓다는 장점을 지닌다. 현재 개발된 LED와 마이크로프로세서 기술은 이와 같은 가변색 광원을 만들기에 가장 적당한 것들이라고 판단하여 LED를 이용한 가변색 광원을 연구, 시제품을 제작하였다. 그리고, 개발된 가변색 광원의 응용분야와 가능성, 거기에서 파생될 수 있는 문제점을 분석하여 제시하였다.
-
This report investigates the road lighting systems by using the road lighting simulation system which is the 'Lightscape', and compares the result of the simulation with criterion of the road lighting system. The solution of that is almost equal to the criterion of the road lighting system. With this simulation, we hope to accurately investigate the criterion of the road lighting systems and design the road lighting systems effectively.
-
본 연구에서는 조명설계·시공과 관련하여 설계초기 단계에서 조명이 실시된 공간에 대하여 어떠한 조명 시스템이 경제적으로 유리한가를 검토하기 위한 수단으로 Worksheet를 개발하고 일반적인 사물실과 고천정 공장에서의 각종 시스템에 대한 평가를 수행하였다. 앞으로 조명설계시 광원, 등기구를 선정하는데 있어서 개발된 Worksheet를 이용하여 조도계산 및 경제성을 평가해 봄으로써 같은 비용으로 최대의 효과를 가진 조명시스템을 선택하는데 도움이 되리라 기대된다.
-
In this paper we develop an electronic starter circuit that is suitable for Neon sign operation of switch-start fluorescent lamps. The developed starter enable single pulse ignition of fluorescent lamp at the peak point of preheating current, irrespective of the position of the Tum-On signal. This is possible due to the sequential operation of two transistors different in their operation characteristics and a diode operation characteristic. The switching endurance test using this starter has been carried for more than 3000 hours for a single switch-start on a severe blinking condition of preheating of 0.1s and of successive lighting interval of 0.1s.
-
도로터널 조명설비의 합리적인 설계로 도로터널의 안전한 교통운행 확보와 쾌적한 운전 환경을 위하여 Computer Simulation Program을 이용한 최적의 터널조명환경을 조성하고 그 결과를 분석·검토하여 설계에 적용하고 조명설비 공사에 반영하며, 발생하는 문제점과 그 대책을 제시하고자 한다.
-
This parer proposes fuzzy reasoning algorithm for improvement in Zonal Cavity Method that is difficult to calculate average illumination without lighting scope and reflection factor so on. This parer use fuzzy reasoning algorithm for maintainment of the best illumination in spite of some variation those are influenced of room illumination and cut down the difficult to be calculated used Zonal Cavity Method.
-
본 논문에서는 91[W] 저압 나트륨 램프용 고효율 전자식 안정기를 제작하여 전기적 특성을 측정하였다. 개발된 고효율 전자식 안정기는 입력 전압 220[V], 입력 전류 435[mA], 입력 전력 94[W], 역률은 98[%], 전류 고조파 함유율 19[%]로 측정되었다.
-
We measured stand-by power of electrical machinery and appliance which are used at office and house. And we estimated potential electrical energy saving through stand-by power and the expecting number of supplied apparatus. As a result, We can reduce electrical energy by minimizing a stand-by power consumption up to three billion kWh which are equal to about 1/3 of an atomic power plant's generating power of 1 year.
-
Many control techniques have been proposed in order to improve the control performance of discrete-time domain control system. In the position control system using a DC servo motor as control system, the response-characteristic of system is controlled by the I-PD controller. In the I-PD longer if gains of I-PD controller are unsuitable. In this paper, therefore, a expanded I-PD control system is constructed by inserting a pre-compensator at out terminal of I-PD controller. It is implemented by neural network with two hidden layers. From the result of computer simulation in the proposed control algorithm, its usefulness is verified.
-
In this paper, we consider to apply of 2-DOF (Degree of Freedom) PID controller at D.C servo motor system. Many control system use I-PD, PID control system, but the position control system have difficulty in controling variable load and changing parameter. We propose neural network 2-DOF PID control system having feature for removal disturbrances and tracking function in the target value point. The back propagation algorithm of neural network used for tuning the 2-DOF parameter (
$\alpha$ ,$\beta$ ,${\gamma}$ , η). We investigate the 2-DOF PID control system in the position control system and verify the effectiveness of proposal method through the result of computer simulation. -
In many fields of automation, increasingly high demands are being placed on the availability and fault tolerance of programmable logic controller(PLC). Particularly in fields where a plant shutdown would be extremely expensive. In such cases, only redundant systems can offer the standard of availability required. The redundant configurations contain more then would normally be necessary for the relevant function. Fault tolerant systems will normally continue to operate even if one or more faults cause parts of the control system to fail.
-
This paper presents a novel Power Factor Corrected(PFC) single-stage AC/DC Half-Bridge converter, which features discontinuous conduction mode(DCM) and soft-switching. The reduced conduction losses are achieved by the employment of a novel power factor correction circuitry, instead of the conventional configuration composed of a front-end rectifier followed by a boost converter. To identify the validity of the proposed converter, simulated results of 500[W] converter with 100[V] input voltage and 50[V] output voltage are presented.
-
Although the switched reluctance motor (SRM) has a several advantages such as simple magnetic structure, robustness, wide range of speed characteristics and simple driving, it has a considerable inherent torque ripple and speed variation duet to the driving characteristics of pulse current waveform and the nonlinear inductance profile. The high torque ripple and speed variation inhibits wide application. The minimization of the torque ripple is very important in high performance servo drive applications, which require smooth operation with minimum torque pulsations. This paper presents the new SRM torque modeling technique for the control of instantaneous torque. The SRM is modeled by the database of torque profiles for every small variation in currents and rotor angles, which is inferred from the several measured data by the adaptive neuro-fuzzy inference technique. Simulation results demonstrating the effectiveness of proposed torque modeling technique are presented.
-
Insulation diagnosis techniques of power equipments for the stable power supply and prevention from accidents are of high importance. Diagnosis techniques is able to prevent from large accidents before they happen by finding signs of the accidents. From this point of view, this paper simulated discharge progress and partial discharge using needle-plan electrode system in air, studied the distribution of frequency spectrum of the radiated electromagnetic waves using biconical antenna and spectrum analyzer. From results of this study, the new method was introduced for measurement and analyzation of the radiated electromagnetic waves in accordance with discharge progress in air, Besides, according to the consideration of the mutual relation between frequency spectrum of the radiated electromagnetic waves and discharge progress, it was confirmed that detecting partial discharge and estimating discharge progress were possible.
-
This paper describes Trans-less type utility interactive system that is combined with buck/boost chopper applying partial resonant method, which remove Trans, and high efficient PWM inverter. Therefore, it is possible to make it lightweight, to cut down the cost, and to improve its reliability. What the merits of this system are that we con transmit arbitrary power to load and utility regardless of generating voltage magnitude and we can always obtain high factor controlling by equal phase signal with utility.
-
Out of the defects occurred in a transformer, the cases of protrusion and surface discharge were simulated by using needle-plane and IEC(B) electrode. The waveform and frequency characteristics of ultrasonic signals due to partial discharge occurred at each electrode were analyzed. And then, the ultrasonic signal characteristics from the partial discharge due to the two kinds of defect were compared. As a result, in the case of the protrusion and surface discharge, the waveforms were similar, but the frequency spectra were different.
-
This paper describes the characteristics of PD pattern and acoustic signal for the possible four states of particles in GIS. For each case of defect, the PD patterns and acoustic signals were measured and analyzed. As a result, the characteristics of the discharge patterns and ultrasonic signals depending for each defect state could be distinguished. Using the discharge patterns and ultrasonic signal waves, the defects in the GIS and the states of the particles can be distinguished.