We prepared ZnO:Al (AZO) thin films on polycarbonate (Pc) and polyethersulfon (PES). Because the polymer substrate has weak thermal resistance. The AZO thin films were deposited at room temperature by facing targets sputtering (FTS) method In the work, AZO thin films were deposited with different thickness in 1mTorr and $O_2$ gas flow rate 0.05. The electrical, optical and crystallographic properties were measured From the results, the resistivity of $7.3{\times}10^{-4}{\Omega}cm$ and transmittance of over 80% in visible range were obtained.

Carbon nanotubes (CNTs) effects on physical properties of the liquid crystal and twisted nematic (TN) liquid crystal (LC) cells have been investigated. The minute doping of CNTs reduces rotational viscosity of the LC, and thus switching time of the TN cells is improved, especially in grey scale response time. In addition, the dielectric anisotropy and birefringence are not affected by such a small amount of CNT-doping and thus voltage-dependent transmittance remains the same.

We have studied effect of Patterned Vertical Alignment (PVA) mode on electro-optical characteristics and stability of liquid crystal director upon electrode pattering. In the present studies, LC director field and stability of conventional PVA mode electrode patterns were analyzed and new type of electrode patterns were suggested. At last, comparison between this new type of electrode patterns to conventional electrode pattern types were followed.

We have studied the viewing angle control using a twist nematic liquid crystal display (TN-LCDs). These TK-LCDs have the characteristics, of which is not good image quality, for examples low Contrast ratio and gray scale inversion problems at upper and down viewing direction. TN-LCDs have the function of switching between the wide viewing mode and narrow viewing angle mode using two tilted LC layers. Tilt angles of the two LC layers, $14^{\circ}$ and $60^{\circ}$ were required in both wide viewing angle and narrow viewing angle modes, respectively. Consequently, this device is compatible with two image performances of which the wide viewing angle mode and Narrow viewing angle mode.

Electrowetting phenomenon is applied in the various field of technology. One of that is electrowetting display as a paper like electronic paper. Fast response and easy to express a color is goodness. In spite of that, the oil movement of the electrowetting display is irregular. So it doesn't look like uniform. Because of the above reason, electrowetting display using patterned electrode is made and the characteristic of oil movement is observed. Electrode and polymer wall is patterned by photo-lithography. We analyze the oil movement according to the variation of size and the position of etched electrode area.

OLEOs was fabricated by PLD method. Wet etching process and plasma treatment of ITO on the glass were performed to extend the lifetime of the OLED and increase its brightness. The NPB, $Alq_3$, Li-Benzoate and AI layers on ITO pattern on the glass were deposited by PLO method, sequentially. When the etched ITO was treated by $O_2$ plasma with RF power of 50W, the best result was obtained. The lifetime of the OLED treated by $O_2$ plasma was extended from 3,770sec to 12,586sec compared to that without the plasma treatment.

ITO/ polytetrafluorethylene (PTFE)/ Tris(8-hydroxyquinolinato Aluminum ($Alq_3$)/ Al 구조에서 정공 수송층 PTFE의 두께 변화에 따른 유전특성은 HP 4284A precision LCR Meter를 이용하여 주파수에 따른 임피던스와 위상각, 유전손실, 그리고 커패시턴스를 측정하였다. 측정 결과 PTFE의 두께가 증가할수록 임피던스 값은 증가하고, 위상각은 저주파수 영역에서는 두께가 증가할수록 감소하다가 고주파수 영역에서는 거의 같아지는 것을 확인하였다. 또한, 유전손실도 저주파수 영역에서는 정공 수송층이 증가할수록 감소하다가 고주파수 영역에서는 거의 같아졌고, 커패시턴스는 PTFE의 두께가 증가함에 따라 작아지고 주파수가 높아질수록 감소함을 확인하였다.

Organic light-emitting diodes(OLEOs) are attractive because of possible application in display with low operating voltage, low power consumption, self-emission and capability of multicolor emission by the selection of emissive material. We investigated the effects of deposition rate on the electrical characteristics, physical characteristics and optical characteristics of OLEOs in the ITO(indium-tin-oxide)/N.N'-diphenyl-N,N'-bis(3-methyphenyl)-1,1'-biphenyl-4,4'-diamine(TPD)/tris(8-hydroxyquinoline)aluminum($Alq_3$)/Al device. We measured current density, luminous flux and luminance characteristics of devices with varying deposition rates of TPD and $Alq_3$. It has been found that optimal deposition rate of TPD and $Alq_3$ were respectively $1.5{\AA}/s$ from the device structure. An AFM measurement results, surface roughness of the deposited film was the lowest when deposition rate was $1.5{\AA}/s$.

In this paper, the inorganic multi-layer thin film encapsulation was newly adopted to protect the organic layer from moisture and oxygen. Using the electron beam, Sputter, inorganic multi-layer thin-film encapsulation was deposited onto the Ethylene Terephthalate(PET) and their interface properties between inorganic and organic layer were investigated. In this investigation, the SiON SiO2 and parylene layer showed the most suitable properties. Under these conditions, the WVTR for PET can be reduced from a level of $0.57\;g/m^2/day$ (bare subtrate) to 1*10-5 g/$m^2$/day after application of a SiON and SiO2 layer. These results indicates that the PET/SiO2/SiON/Parylene barrier coatings have high potential for flexible organic light-emitting diode(OLED) applications.

Top emission OLED 소자에 사용되는 ITO(Indium-Tin-Oxide)의 저항을 개선하여 보다 낮은 저항을 가지는 전극을 제작하기 위해 AZO(ZnO-Ag-ZnO)를 제작하였다. AZO박막은 기존의 ITO 박막이 수십 $\Omega$을 나타내던 것과 비교하여 $8{\Omega}$으로 매우 낮은 저항을 나타내었다. 투과율은 84%로 기존의 ITO 박막과 유사한 성능을 나타내었다.

In this paper, the inorganic-organic thin film encapsulation layer was newly adopted to protect the organic layer from moisture and oxygen. Using the electron beam, Sputter and Spin-Coater system, the various kinds of inorganic and organic thin-films were deposited onto the Ethylene Terephthalate(PET) and their interface properties between organic and inorganic layer were investigated. Results indicates that the SiON/PI/SiON/PI/PET barrier coatings have high potential for flexible organic light-emitting diode(OLEO) applications.

In this paper, the characteristics of polycrystalline silicon thin-film transistors (poly-Si TFTs) fabricated on polymer substrates are investigated. The a-Si films was laser annealed by using a XeCl excimer laser and a four-mask-processed poly-Si TFT was fabricated with fully self-aligned top gate structure. The fabricated nMOS TFT showed field-effect mobility of $30cm2/V{\cdot}s$, on/off ratio of 105 and threshold voltage of 5 V.

We studied the nematic liquid crystal (NLC) alignment capability by the IB(on bean) alignment method on a NDLC(Nitrogen Diamond Like Carbon) as a-C:H thin film, and investigated electro-optical performances of the IB aligned IPS(In plane switching}cell with NDLC surface. A good LC alignment by IB exposure on a NDLC surface was achieved. Monodomain alignment of the IB aligned IPS cell can be observed. The goodelectro-optical (EO) characteristics of the IB aligned IPS cell was observed with oblique IB exposure on the NDLC as a-C:H thin film for 1 min.

We studied nematic liquid crystal (NLC) alignment effect on the $SiO_x$ thin film deposited $45^{\circ}$ oblique by rf magnetic sputtering system. Pretilt angle and thermal stability characteristic as well as NLC alignment effect were investigated. A uniform liquid crystal alignment effect on the $SiO_x$ thin film was achieved and pretilt angle was about $90^{\circ}$. The thermal stability of the $SiO_x$ thin film was sustained by $200^{\circ}$.

Eye Glass Display(EGD)의 광학계를 소형, 경량화 하기 위하여 OLED 마이크로 패널과 프리즘 렌즈를 사용하여 설계하였다. 광학계 설계에 사용된 OLED 마이크로 패널은 0.59"크기의 SVGA($800{\times}600$)급이며, 크기는 0.59"이며, 렌즈는 프리즘 렌즈로 설계되었다. 설계된 프리즘 렌즈는 3연으로 구성되었으며, 각 면은 각각 비회전대칭 비구면으로 tilt와 decenter를 사용하여 광학적 성능을 향상시켰다. 설계된 프리즘 렌즈의 화각(FOV)은 $28^{\circ}$, 왜곡수차는 4% 이내이며, 광학계의 해상도를 나타내는 MTF는 공간주파수 30lp/mm에서 full field가 40%이상의 성능을 나타내었다.

High quality $Bi_2Sr_2Ca_nCu_{n+1}O_x$ superconducting thin films fabricated by using the evaporation method at various substrate temperatures, $T_{sub}$, and ozone gas pressures, $pO_3$. The correlation diagrams of the $Bi_2Sr_2Ca_nCu_{n+1}O_x$ phases with $T_{sub}$ and $pO_3$ are established in the 2212 arid 2223 compositional films. In spite of 2212 compositional sputtering, Bi2201 and Bi2223 as well as Bi2212 phases come out as stable phases depending on $T_{sub}$ and $pO_3$. From these results, the thermodynamic evaluation of ${\Delta}H$ and ${\Delta}S$, which are related with Gibbs' free energy change for single Bi2212 or Bi2223 phase, was performed.

We have investigated dielectric properties depending on temperature in organic light-emitting diodes using 8-hydroxyquinoline aluminum ($Alq_3$) as an electron transport and emissive material. We analyzed the dielectric properties of organic light-emitting diodes using characteristics of impedance. he Impedance characteristics was measured complex impedance Z and phase $\theta$ in the temperature range of 10 K to 300 K. We obtained complex electrical conductivity, dielectric constant and loss tangent ($tan{\delta}$) of the device at room temperature. From these analyses, we are able to interpret a conduction mechanism and dielectric properties contributed by an interfacial and orientational polarization.

유기발광소자의 주파수 응답 특성은 계면에서의 특성을 파악하는데 유요한 도구이다. 온 연구는 유기발광소자의 재료로 널리 알려진 $Alq_3$를 이용하여 소자를 제작한 후, 주파수 응답 특성을 이용하여 $Alq_3$의 등가회로를 해석하였다. 또 온도에 따른 용량성분을 분석하여 $Alq_3$에 인가된 전압에 따라 용량성분의 변화를 살펴보았다. 용량성분의 변화는 낮은 주파수 영역에서는 나타나지 않다가, 높은 주파수 영역에서 온도에 따라 미묘하게 감소하는 것을 볼 수 있다. 이는 낮은 주파수 영역에서 높은 주파수 영역으로 변화하면서 소자 내의 주된 성분이 저항성분에서 용량성분으로 변화하는 것을 의미하며 높은 주파수에서 온도에 따른 용량성분의 변화를 찾을 수 있었다.

The hybrid thin-film (HTF) passivation layer composed of the Ultra Violet (UV) curable acrylate layer and MS-31 (MgO:$SiO_2$=3:1wt%) layer was adopted in organic light emitting device (OLEO) to protect organic light emitting materials from penetrations of oxygen and water vapors. The results showed that the HTF layer possessed a very low WVTR value of lower than $0.007gm/m^{2+}day$ at $37.8^{\circ}C$ and 100% RH. This value was within the limited range of the sensitivity of WVTR measurements. And the lifetime of the HTF passivated device became almost three times longer than that of the bare device. The HTF on the OLEO was found to be very effective in protect what from the penetrations of oxygen and moisture.

Doping is a well-known method for improving electroluminescent (EL) efficiency of organic light emitting diodes. In our study, doping with 2 materials simultaneously, we could achieve improved EL efficiency. The emission layer was tris-(8-hydroxyquinoline)aluminum, and the 2 dopants were N,N'-dimethyl-quinacridone (DMQA) and 10-(2-Benzothiazolyl)-2, 3, 6, 7-tetrahydro-1,1,7,7,-tetramethyl 1-1H, 5H, 11H-[1] benzopyrano [6,7,8-ij]quinolizin-11-one (C-545T). The EL intensity of co-doped device was nearly flat, it shows that co-doping technique could be a effective way to improve the EL efficiency. EL efficiency of Single-doped device based on DMQA and C-S45T were ~6.47Cd/A and ~7.45Cd/A, respectively. Co-doped device showed higher EL efficiency of ~8.30Cd/A.

ITO/4, 4', 4"-tris (N -3 - methylphenyl - N - phenyl - amino) - triphenylamine, [m-MTDATA] / Terbium Iris - (1 - phenyl - 3 - methyl - 4 - (tertiarybutyryl) - pyrazol - 5 - one) triphenylphosphine oxide [$(tb-PMP)_3Tb-(Ph_3PO)$] / Mg:Ag devices were made to investigate its electrical and light emission properties. The thickness of m-MTOATA layer was varied from 0 to 80 nm. There was a threshold thickness for the sufficient hole injection. The insertion of 20 nm thick m-MTDATA layer between ITO and Tb-complex resulted in the right shift of current-voltage curve because of the insufficient hole injection. The low operating voltage can be obtained above the 40 nm of m-MTDATA layer. The insertion of m-MTDATA induced the increase of the background in the electroluminescence spectrum which was dependent on the current density of the devices.

The transport properties of amorphous selenium typical of the material used in direct conversion x-ray imaging devices are reported. The effects of As addition on the carrier mobility and recombination lifetime in amorphous selenium (a-Se) films have been studied using the moving photocarrier grating (MPG) technique. We have found an increase in hole drift mobility and recombination lifetime, especially when 0.3% As is added into a-Se film, whereas electron mobility decreases with As addition due to the defect density. The transport properties for As doped a-Se films obtained by using MPG technique have been compared with the drift mobilities of holes and electrons obtained by time of flight (TOF) measurement.

Electro-optical (EO) characteristics of in-plane switching (IPS) cell on the polyimide surface using obliquely ion beam (IB) exposure as new ion beam (IB) type system (DuoPIGatrion ion source). A good uniform alignment of the nematic liquid crystal (NLC) alignment with the ion beam exposure on the polyimide surface was observed. In addition, it can be achieved the good EO properties of the ion-beam-aligned IPS-cell on poly imide surface ; the stable VT curve in the ion-beam-aligned IPS cell on a poly imide (PI) surface with ion beam exposure using new type IB equipment was obtained. and the fast response time in the ion-beam-aligned IPS cell on a polyimide (PI) surface with ion beam exposure using new type IB equipment was obtained.